Reference chart

Tungsten electrode amperage chart by diameter

The number distributors get asked most, on one page: which diameter carries which current, in DCEN and AC. Figures follow equipment manufacturers' published guidance for argon shielding — read the limits, then set your procedure.

Tungsten electrode amperage chart — diameter vs current, argon shielding, 150/175 mm land
DiameterInchDCEN (A) — WT20 / WC20 / WL15 / WL20 / WY20DCEP (A) — WP / WZ8AC balanced (A) — aluminium, WP / WZ8Order
1.0 mm0.040″15–80—15–50Quote
1.6 mm1/16″70–150—60–120Quote
2.0 mm0.080″125–220—80–150Quote
2.4 mm3/32″150–250120–18080–150Quote
3.2 mm1/8″250–400180–250150–250Quote
4.0 mm5/32″400–500250–350200–320Quote
4.8 mm3/16″500–750350–460290–390Quote
6.4 mm1/4″750–1000460–600390–590Quote

How to read this chart without getting burned

The upper limit is the real limit. Below the range you lose penetration and the arc drifts; above it the tip melts, spits tungsten into the weld pool, or grows a mushroom head. Over-current is the usual cause when a welder blames electrode quality — in practice a rod run 10–15 % past its ceiling can lose most of its usable life.

Diameter tracks current, geometry tracks the joint. If your amperage sits at the very bottom of a row, take the smaller diameter and grind a long needle taper with fine, axial grinding marks (240 grit or finer). A correctly prepared 2.4 mm will happily run thin stainless well under 150 A; a badly ground one will not start cleanly at any current.

Polarity moves the numbers more than brand does. The DCEN column assumes electrode negative. Switch to DCEP, or to AC for aluminium, and the same rod carries far less current — which is why a balled WZ8 or WP tip is chosen for AC while thoriated and lanthanated rods are kept for DC.

Where the figures come from (and where they stop)

These are published general-guidance ranges from welding equipment manufacturers' technical literature, measured with argon shielding at normal electrode stick-out. ISO 6848 does not define current — it defines classification and colour coding only. Two variables shift every number on this page:

Shielding gas

Helium blends and higher flow raise the arc's energy, so reduce current against the chart. Pure argon at 10–15 L/min is what these figures assume.

Procedure qualification

For coded or pressure work, your WPS governs, not a chart. Use this page to pick a diameter, then confirm within your qualified window.

Choosing between two rows

The rows are not evenly spaced, so interpolation is where buyers get hurt. A 2.4 mm tops out around 250 A, while 3.2 mm opens at 250 A — a job that runs continuously at 250 A belongs on the 3.2 mm, because the smaller rod is sitting at the very ceiling of its duty and will burn its tip back between dressings. Choose the row whose middle covers your working current, not the one whose edge just touches it.

DCEP and balanced AC carry far less current than DCEN on the same diameter, which is why aluminium work usually steps up a size relative to stainless. Below 2.4 mm the DCEP column is intentionally left blank: running electrode positive on a thin rod is not a normal process choice, and the tip will not hold a stable ball.

Buyer's note for distributors

Stock the diameters that match your region's machines, not the whole matrix. In European workshops 1.6 / 2.4 / 3.2 mm in 175 mm carry most volume; North American RFQs ask for the inch equivalents and often 6″ (150 mm) for heads. We ship mixed cartons across these sizes with the same MOQ counting as one order — see packaging & OEM and the full size matrix.

Send your electrode list today

Type, diameter × length, quantity and packing — mixed sizes welcome. You get a specification-confirmed quotation with lead time, normally within 24 hours.

WhatsApp